Skip to content


how to change a jeep wrangler headlight bulb? SUPAREE

How To Change A Jeep Wrangler Headlight Bulb?

A lot of owners are asking such questions, we read it and think we can help you, I think we should also send our operation method to the Internet, so that those who like DIY as I do as a reference, but also to repay the following to give me reference to the netizens.
First of all, this is a replacement bulb, not a headlight assembly, I personally feel that save money not to mention, at least to ensure that its original headlight penetration, in addition to many people like the colour temperature in the 4200k above the white light colour, indeed, than the yellowing light bright, and xenon and led lights are brighter than 2500 lumens than halogen 1500 lumens a lot, but the penetration or yellowing light strong (look at the color of the street lamp will know). The colour of the street light will know), too strong light will bring danger to the opposite car, or to pay attention to this point
Okay, here's the job

  1. Prepare tools, have a T15 screwdriver
  2. Removal of concealed grille fasteners
  3. Removing grids
  4. Removing the jeep headlights
  5.  Change The Bulb
  6. Back to fitting jeep headlights
  7. Reassemble All The Parts

1.Prepare tools, have a T15 screwdriver



If you have some of the components below, that will help, nothing more.

Extra or new headlight bulbs
T15 plummer screwdriver


2.Removal of concealed grille fasteners


To take off the center mesh, you need to pry off all the plastic clips on the center mesh.

Pry the middle one first

And then pry off the whole

The six concealed buckles are taken down into a small box do not lose, adjust the concealed buckle with two tools from both sides at the same time warp more convenient, but also does not damage the concealed buckle.


3.Removing grids

Points: from the side of the figure force to the front direction of the car pull (or their own direction) note that when pulling the two hands that the grille up and down together first from one side of the force, to have a little violence but pull the trip (distance to be short) to take off and put to the side.


4.Removing the jeep headlights

Now use the T15 tool to unscrew the four screws on the headlight, and then take down the lamp cup ring cover, the lamp cup will be pulled down, hand after reaching the lamp cup a pull to pull down the jack socket, and then pull the wide lamp with the lamp holder from the rubber ring belowPut it somewhere nearby. Look, the whole headlight is in your hands.


5.Change The Bulb

 Now rotate the bulb counterclockwise and the old bulb will come out. Bring the new bulb and place it in the original position. How easy it is! But here are some things you have to remember when you want to set it to the way it was before!

6.Back to fitting jeep headlights

Now turn the bulb anti-clockwise, and the older bulb will come out. Bring the new one and set it where the older one was placed. How simple it was! But here you have to remember something when you will set it as it was before!


6. Reassemble All The Parts:

Maybe you have changed the bulbs. Now you have to go back to the older process. Turn a new bulb clockwise and plug it with the red clip connector.

Set everything in the headlight position, including the silver ring. Tight every nut and bolt with Torx. Finally, unite the whole front grill, how you opened it, and Close the hood.

 Just a few simple steps to do it yourself can easily replace the jeep bulb, hurry up and try it yourself!

Previous article What is the difference between Jeep Halogen and LED headlights?
Next article What is Headlight Sensitivity Jeep Compass?


L Francell - February 20, 2024

Can you please post images on this blog with recommendations on how to run and install the wiring? I am concerned about the heat around the radiator and running the RGB wire and fog lamp wires. They are not long enough to reach back around the engine compartment to each side. How did y’all install the wires?

Leave a comment

Comments must be approved before appearing

* Required fields

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare